Glass and Carbon Reinforcement Fabrics: Areal Weight and How Much Cloth a Layup Needs
A composite such as fibreglass or carbon fibre is a textile set in plastic. The fabric, woven or stitched from glass or carbon fibres, provides the strength and stiffness; the resin binds it, transfers load between the fibres and gives the part its shape. That makes composite work one of the places where textile arithmetic matters most, because the reinforcement is bought, cut and laid up by area and weight. This guide explains how reinforcement fabrics are specified, what "200 g/m² 3K twill" actually means, and how to work out how much cloth a layup needs, using the site's Fabric Weight from Dimensions, Fabric Yardage Calculator and yarn count converter.
The main kinds of reinforcement fabric
- Woven cloth. Glass or carbon yarns woven in plain, twill or satin weaves. Plain weave is stable and easy to handle flat; twill drapes better over curves and is the familiar look of visible carbon parts; satin drapes best of all.
- Chopped strand mat (CSM). Short glass strands held together by a binder. Cheap, builds thickness quickly and conforms easily, but needs more resin and is weaker than woven or stitched fabric for its weight.
- Woven roving. A coarse, heavy weave of flat glass bundles, used to build strength quickly in boat hulls and tanks.
- Stitched multiaxials. Layers of straight, unwoven fibres at set angles (for example 0/90 or plus and minus 45 degrees) held together by light stitching. Because the fibres are not crimped over and under each other, they carry load efficiently.
- Unidirectional fabric. Almost all the fibres run one way, for parts loaded mainly along one axis.
Areal weight: the number every reinforcement is sold by
Reinforcement fabrics are specified by areal weight, in grams per square metre, exactly like any other fabric's GSM. A light glass cloth for surface finishing might be under 100 g/m²; general-purpose carbon twill is often around 200 g/m²; chopped strand mat is commonly sold at 300 or 450 g/m². The Fabric Weight Converter turns those into ounces per square yard for suppliers who use them: 200 g/m² is 5.9 oz/yd² and 300 g/m² is 8.85 oz/yd².
Areal weight matters more in composites than in clothing because it controls how thick and strong each ply is and how much resin it takes up. Designers often specify a laminate as a number of plies of a named fabric, so swapping to a heavier or lighter fabric changes the part.
What "3K" means, and converting tow sizes
Carbon fibre is made as continuous filaments only a few micrometres across, gathered into a bundle called a tow. The K number is the filament count in thousands: a 3K tow has about 3,000 filaments, a 12K tow about 12,000. Tows are also described by linear density. For a common standard-modulus 3K carbon, the figure is in the region of 200 tex, meaning 200 g per 1,000 m of tow; check your supplier's data sheet for the exact value, because it depends on the fibre grade.
The yarn count converter shows the same tow in the other systems: 200 tex is 1800 denier and 2000 dtex. A 6K tow of the same fibre is about twice that, 400 tex, or 3600 denier. Larger tows weave into heavier or more open fabrics; a 200 g/m² twill is usually 3K, while 12K tows are typical of heavier or cheaper fabrics. Glass rovings are described the same way, by tex, which makes the converter useful when comparing data sheets from different regions.
Worked example: how much cloth does a layup need?
Suppose a part needs four plies of 200 g/m² carbon twill, and each ply covers 1.2 m² once you allow for its trimmed outline. That is 4.8 m² of cloth in the finished part.
- Dry fabric weight in the part. The dimensions tool gives 4.8 m² at 200 g/m² as 960 g, a little under a kilogram of carbon.
- Length to buy. Reinforcement is often sold on rolls around 127 cm wide. Entering 4.8 m² of area, 127 cm of usable width and a 25% waste allowance into the yardage calculator gives 3.78 m before waste and 4.72 m to buy, or 5.17 yards. If the cloth comes on 50 m rolls, that is a single roll.
- Weight of what you buy. 4.72 m of 127 cm cloth at 200 g/m² is 5.99 m², or 1.2 kg.
The waste allowance does a lot of work here. Composite plies are often cut at an angle to the roll, for example at 45 degrees to the warp, to orient the fibres where the load runs, and angled plies waste far more cloth than squares cut along the roll. A 25% allowance is a placeholder; a nesting plan on paper or in software will tell you the real figure for your shapes. The calculator also assumes plies can be pieced anywhere across the width, which is rarely true for a structural part, so check that each ply fits the roll width in one piece.
Resin quantity
Resin is the other half of the material bill. Resin suppliers publish guidance for each product and process, and you should follow it. As a very rough illustration, hand lay-up of woven cloth often takes something like its own weight in resin, so the 960 g of carbon above might need in the region of another kilogram of mixed resin, while chopped strand mat takes considerably more resin per gram of glass. Vacuum bagging and infusion use less resin and give a stronger, lighter part. Mixed resin has a limited working time, so measuring by weight from the fabric weight helps you avoid mixing more than you can use.
Handling and cutting
- Cut with the right tools. Sharp shears or a rotary cutter for woven glass and carbon; dull blades fray the edges and distort the weave.
- Keep the weave square. Woven reinforcements, especially satins and loose twills, distort easily when handled, which shifts fibre angles in the part. Some fabrics are sold with a light binder or a backing to help.
- Label the plies. In a multi-ply laminate, orientation and order matter. Mark the warp direction and the ply number on each piece.
- Store clean and dry. Moisture and dust on dry fabric weaken the bond with the resin.
Health and safety
Composite work involves real hazards, and this guide is about fabric quantities, not safe practice. In brief: uncured epoxy can cause skin sensitisation that becomes lifelong, so avoid all skin contact; polyester and vinylester resins give off styrene vapour that needs good ventilation; and cutting, trimming and sanding glass or carbon produces dust and fibres that irritate skin, eyes and lungs, while carbon dust is also electrically conductive. Read the safety data sheet for every resin, hardener and fabric, wear the gloves, eye protection and respiratory protection it specifies, and work with proper ventilation and dust extraction.
If a composite part will carry load where failure could hurt someone, such as on a vehicle, an aircraft, a boat hull, climbing or lifting gear, or a structure, the laminate design belongs to a qualified engineer. Ply counts and fabric weights copied from another project are not a substitute for a design.
What the tools cover
The site's tools handle the textile arithmetic: areal weight in either unit, the weight of a given area of cloth, the length to buy for a given width and waste allowance, and tow or roving sizes across the yarn count systems. They do not model fibre orientation, resin content, cured thickness, stiffness or strength, all of which depend on the fabric, the resin and the process together. For those, the fabric and resin manufacturers' data sheets are the place to start.